GLOAPM.COMNach Rang
Nach Rang
Nach Schiffstyp
Auf der Karte
Nachrichten und Schulungsmaterialien
Für Segler
Für Unternehmen
Suche nach aktuellen Stellenangeboten:
Filter anzeigen
Lebenslaufsuche für Seeleute:gemeinsame Basismeine Basis
Heim Online-Tests CES Slow Speed 3rd-Eng/4rd-Eng Test for specialists working in Engine room (CES v6.0)
Online-Test: Test for specialists working in Engine room (CES v6.0)
Wählen Sie den Testmodus:
Ausbildung
Online-Test
Beschreibung
Rezensionen
Der Test besteht aus 80 zufälligen Fragen.
Gesamtzahl der Fragen zu diesem Thema: 147
Gesamtzahl der Fragen zu diesem Thema: 147
Frage 1 aus 80
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
- 75
- 76
- 77
- 78
- 79
- 80
A large electric motor is being removed from a main seawater pump with the aid of the engine room crane. Which is the best method of starting the lift from the options given?
Use the full hoist facility on the crane to “break” the motor free after slackening all of the retaining bolts.
Use the “inch up” facility on the crane to “break” the motor free after slackening all of the retaining bolts.
Use a suitable chain block suspended from the crane hook to “break” the motor free after slackening all of the retaining bolts.
Use the full hoist facility to lift the motor clear in one action after removing all of the retaining bolts.
For ideal synchronising as the incomer circuit breaker contacts make, the phase angle difference between the incomer e. m. f. and the busbar voltage should be:
30° behind.
0°.
90° lag.
30° ahead.
For a Nitrite – Borate based cooling water treatment system, what would be considered to be the normal nitrite concentration limits for a correctly dosed system?
3 000 – 4 500 ppm Nitrite.
1 500 – 3 000 ppm Nitrite.
0 – 1 500 ppm Nitrite.
4 500 – 6 000 ppm Nitrite.
What is the expansion ratio of the foam produced by the fixed low-expansion foam fire-extinguishing system of an engine room?
Less than 20 to 1.
Less than 5 to 1.
Greater than 20 to 1 but less than 50 to 1.
Less than 12 to 1.
What is the disadvantage of using chemicals on an oil-spill on the water?
It is difficult to apply the chemicals if the oil drifts away from the ship’s side.
The chemicals make it difficult to remove the oil from the water.
It is difficult to apply chemicals if there is any wind.
The water gets a white colour, which makes it easy to detect the oil-spill.
Which component does this graphical symbol illustrate?
PH analyzer.
Pressure indicator, installed on panel/console.
Pressure indicator, installed locally.
Pressure relief valve, self-contained.
What is the correct method to use for fitting a rolling contact bearing, such as a ball bearing, onto a parallel shaft?
Use a hammer and a pipe with the same diameter as the inner bearing ring and knock the bearing onto the shaft.
Use emery cloth on the bearing surface on the shaft.
Use emery cloth on the inner ring (contact surface) of the bearing.
Gently heat the bearing in an oil bath and use a bearing puller to draw it onto the shaft.
An earth fault exists on the blue line of a 100 A bilge pump circuit. A second earth fault occurs on the yellow line of a 10 A ventilation fan circuit. The likely outcome is that:
Both motors trip out on overload.
A short circuit occurs between earth faults and the ventilation fan fuse blows.
A short circuit occurs between earth fault and the bilge pump fuse blows.
An open circuit occurs between earth fault and both motors trip out.
Personnel in a high voltage switchroom smell ozone. Which of the following is the likely cause?
Air circuit breaker problems.
Arcing at badly connected bus bars.
Vacuum circuit breaker problems.
Transformer overload.
Is it always possible to use the word “ship” instead of the word “boat”?
A large vessel is always called a “ship” and never a “boat”.
Normally a small vessel is called a “boat” rather than a “ship”, otherwise it is not important.
Either can be used anytime.
A boat can only be used for vessels under 50 metres in length.
On finding a person apparently unconscious in a High Voltage switch room, which of the following should be done?
Raise alarm then drag the victim clear so that they cannot reach live parts while receiving aid.
Check if the victim is in contact with live parts and if not apply first aid.
Raise alarm, identify means of isolation and apply before approaching victim.
Trip all breakers and approach victim.
In a purifier assuming the separating temperature is correct, what is the probable cause of the processed oil containing water?
The back pressure at the clean oil outlet is too high.
The gravity disc is too small and/or the flow rate is too high.
The throughput is too low.
The gravity is too large.
What cooling medium is normally used to cool the condenser of a fresh water generator?
Air.
Seawater.
Brine.
Distillate (freshwater).
As part of the regular maintenance for a paramagnetic oxygen analyser used for measuring the oxygen content of exhaust gas it is important to keep the sample line filter as clean as possible. Why is this necessary with this type of instrument?
The filter may rupture due to the high pressures generated by the sample pump.
Pressure variations in the sample chamber can cause errors so restrictions must be kept to a minimum.
The pressure drop across the filter may damage the sampling pump.
A high flow rate is required in order to deflect the sensing element.
What is the ideal working temperature for physical work?
-10 °C.
10-15 °C.
21-35 °C.
17-20 °C.
During a bomb search, which of the following is an important principle to follow?
Throw any suspicious items overboard.
Try to reach behind bulkheads to find a bomb.
Do not touch any suspicious packages.
Know exactly what a bomb looks like.
What is the correct name of the part highlighted in the illustration?
Push rod.
Crankshaft.
Camshaft.
Connecting rod.
The lubricating oil in the bearing housing at the turbine end of a turbocharger gets very dirty after only a few hours in service. What is the most likely reason for this happening?
The wrong type of lubricating oil has been used.
Damaged rotor shaft sealing bushes allowing exhaust gas to leak into the bearing housing.
The turbine end bearing is badly worn.
The lubricating oil filling connection screw cap is missing.
What would be the correct form of response to the question: “What kind of assistance do you require?”
The correct form of response would be: “There is a fire onboard my vessel”.
The correct form of response would be: “My vessel has a fire in the accommodation and we require fire-fighting assistance”.
The correct form of response would be: “I need help on board with a fire and the smoke is very toxic”.
The correct form of response would be: “I need help as soon as possible”.
What do you call the wide rung on a pilot ladder that prevents the ladder from twisting?
The wide rung on a pilot ladder that prevents it from twisting is called a “Spreader”.
The wide rung on a pilot ladder that prevents it from twisting is called a “Wide step”.
The wide rung on a pilot ladder that prevents it from twisting is called a “Long rung”.
The wide rung on a pilot ladder that prevents it from twisting is called a “Ani-twist rung”.
What is the correct name of the part highlighted in the illustration?
Crosshead.
Liner.
Bottom end bearing.
Connecting rod.
Why is it important to check the timing of diesel engine cylinder oil lubricators?
To ensure the piston is not covering the lubrication points and blocking the flow of cylinder lubricating oil into the cylinder.
To ensure the correct amount of cylinder lubricating oil is fed into the cylinders.
To ensure cylinder lubricating oil enters the cylinders when the piston is in the required position.
To avoid excess pressure in the cylinder lubrication system.
What does the term “Dead Ship” mean?
“Dead Ship” means that the ship cannot make way through the water.
“Dead Ship” means that the ship is aground.
“Dead Ship” means that the machinery and boilers are inoperational due to lack of electrical power.
“Dead Ship” means that auxiliary machinery is not operational.
Under which circumstances should a sprinkler head of a common fixed sprinkler fire-extinguishing system be activated?
When the smoke density exceeds 12,5 % obscuration per minute, but after the corresponding alarm is acknowledged and assessed at the control panel.
When the temperature is within a range from 68 °C to 79 °C, but after the corresponding alarm is acknowledged and assessed at the control panel.
Automatically, when the temperature is within a range from 68 °C to 79 °C.
Automatically, when the smoke density exceeds 12,5 % obscuration per meter.
When you join a new ship, how are you informed about safety rules, alarm instructions and your own duties in case of an emergency?
By folder distributed to each crewmember.
By muster list exhibited in conspicuous places.
By alarm instructions in all crew cabins.
By oral instructions by the Captain.
A mechanical seal, consisting of carbon and ceramic seal rings, is to be fitted to a centrifugal pump shaft. What is the most likely result of not being extremely careful when fitting this type of seal?
The seal rings are hard and may score the pump shaft.
The spring and bellows for the seal can be easily damaged.
The seal rings are brittle and can be easily chipped or damaged.
The rubber O rings for the seal can be easily damaged.
An important quantity which is useful in circuit analysis is known as conductance G (Siemens). Which of the formulas A to D expresses the conductance for this circuit?
G = 1/R.
G = 2R.
G = R·V.
G = I/R.
B Class divisions in ships are constructed so that they are capable of preventing the passage of flame to the end of a standard fire test held for:
30 minutes.
15 minutes.
60 minutes.
45 minutes.
Personnel in a high voltage switchroom and smell rotten eggs. What may this indicate?
Burning of insulation.
Arcing at badly coupled bus bars.
Problems with a vacuum circuit breaker.
Problems with a gas (SF6) circuit breaker.
What could cause diesel engine lubricating oil to appear cloudy with a slightly “milky” colour?
Fuel contamination of the system.
Oxidation of the oil.
High temperature of the oil.
Water contamination of the system.
What is the approximate content of oxygen in air?
21 %.
99 %.
51 %.
11 %.
What is the correct name of the tool shown in the illustration?
Pliers.
Adjustable wrench.
Chisel.
Open end wrench.
What type of component does this graphical symbol illustrate?
Pressure-reducing regulator.
Pressure switch.
Pressure relief valve.
Flow controller.
A detector that is activated by a rise of temperature is:
A thermic detector.
An optic detector.
A smoke detector.
A detector of radiation.
When you are calibrating an instrument what is the most common second step in the procedure?
Adjustment of Zero-point.
Check linearity.
Adjustment of range.
Adjustment of span.
What action should be taken by the engine room rating if a piece of machinery is not functioning properly?
If machinery does not function properly, the Chief Engineer should be called out immediately.
If machinery does not function properly, it should be immediately stopped every time.
If machinery does not function properly the duty Engineer should be informed immediately so that plans for further action can be made.
If machinery does not function properly, it should be stopped and serviced immediately.
What is the main reason for keeping engine lubricating oil viscosity within recommended limits?
To reduce system pressure losses.
To ensure the strength of the oil film is sufficient to keep lubricated surfaces apart.
It is not important.
To neutralise any acids that may form.
Many large slow speed diesel engines operating on heavy fuel oil have a fuel injection system which features Variable Injection Timing. How does this affect engine operation?
VIT increases engine efficiency by automatically maintaining the maximum cylinder pressure over the entire load range.
VIT allows the ship’s engineers to alter the injection timing for each load setting with a simple single adjustment of the fuel rack.
VIT increases engine efficiency by automatically maintaining the maximum cylinder pressure over part of the load range.
What is one of the main features of the cylinder lubricating oil used in large 2 stroke marine diesel engines which normally operate on heavy fuel oil?
It is neutral with a pH value of 7.
It is a pure mineral oil without any special additives.
It is strongly acidic.
It is strongly alkaline.
While alongside at a repair berth a new section of seawater pipe has been fabricated in a shoreside workshop from drawings supplied by the vessel. During fitting of the pipe by ship’s engineers it is noted that the pipe is too short leaving a gap of about 8 mm between the flange faces. What action should be taken to remedy this problem?
The pipe should be returned to the shoreside workshop for modification or to be remade to the correct dimensions.
The ships engineer’s should use extra long bolts and pull the flanges together.
The ship’s engineers should fit extra thick joints between the flanges to fill the gap.
The ship’s engineers should manufacture a spacer piece to fit the gap.
What is the most important task after carrying out any major overhaul on a diesel engine?
Start the auxiliary blower to ventilate the engine so that it has sufficient fresh air for starting.
Start the engine to check the direction of rotation.
A thorough check inside the engine to make sure all tools and cleaning rags have been removed.
Repair any damaged paint work on the engine.
Give the meaning of the following symbol:
Indicates manual starting direction of the engine.
Start water spray.
Reverse engine.
Start engine.
Modern slow speed, two stroke diesel engines often have locating pins or pegs to keep the piston rings in a fixed position. Why is this arrangement used?
The piston ring gaps can be kept in line to control the gas pressure on each of the rings.
The piston rings are more difficult to lubricate because of the slow operating speeds and will wear more quickly if they are allowed to rotate.
It avoids the risk of the ends of the piston rings being forced out by the gas pressure and catching on the scavenge ports.
It ensures the rings cannot be mixed up and that they are fitted in the correct order on the piston.
A section of seawater pipe has been removed for maintenance. When refitting the pipe after completing the work the bolt holes in the flanges are found to be misaligned. What procedure should be followed to finish the work?
Adjacent pipework should be slackened off to allow the pipe to be aligned. Any incorrectly positioned brackets should be adjusted after the pipe is refitted.
Use a chain block to pull the pipe flanges into alignment and leave it in place after the bolts are fitted to avoid overstressing the bolts.
Use wooden wedges to force and hold the pipe into the correct position and then fit the bolts.
Force the pipe into position and then hammer the bolts into the holes to hold the pipe flanges into alignment.
Why may wearing sweat rags slung round your neck when working in the machinery spaces be hazardous?
The rags may cause sweat rash.
The rags may cause you to get too hot and faint.
The rags may be soaked with oil and catch fire.
The rags may be caught by running machinery or power tools.
The exhaust gas temperatures of all cylinders of a diesel engine are seen to be high. Select, from the options given, the most likely cause of this:
Insufficient cooling of the main bearings.
Poor fuel oil quality.
High wear rate in one of the fuel injection pumps.
One of the fuel cams is worn.
Which of the following fittings shall be provided to all lifeboats?
A manually controlled lamp fitted on the outside.
A remotely operated steering arrangement.
An electric power starting system for the propulsion engine with one rechargeable energy source.
Permanent boarding arrangements on both sides to enable persons in the water to board the lifeboat.
You are witnessing someone about to faint. What are the symptoms?
The person may be very pale, and pulse is slow at first and weak.
The pulse is very fast and the person is getting cold.
The person starts to talk a lot and seems superactive.
Red face and big eyes.
Which of the options represents the best action to take when an item of machinery, which normally operates in automatic mode, is operated in “manual” mode?
Keep the Chief Engineer informed of machines performance on an hourly basis.
Have someone permanently stationed at the machine in case of an operational problem.
Monitor the operation of the machinery on a frequent basis.
Change over all other machinery to manual mode of operation.
What is the correct name of the tool shown in the illustration?
Pliers.
Chisel.
Monkey wrench.
Padlock.
The two instruments necessary for generator synchonising are:
kW meter and frequency meter.
Voltmeter and synchroscope.
Synchroscope and kVar-meter.
Amp-meter and volt-meter.
With regard to radar, what would be a correct form of response to the question: “What range scale are you using?”
The correct form of response would be: “I am using the 12 mile range scale”.
The correct form of response would be: “I am using the largest range scale”.
The correct form of response would be: “I am using the 10 cm radar”.
The correct form of response would be: “I am using the 3 cm radar”.
During an unmanned period on a UMS vessel the “low water level” alarm for the jacket cooling water system expansion tank activities. What action would you take as duty engineer?
Answer the alarm then block the alarm function for later action and resume unmanned operation.
Answer the alarm then block the alarm and change to manned engineroom condition.
Answer the alarm and adjust the alarm set point for the water level in the expansion tank before resuming unmanned operation.
Answer the alarm, top up the tank and check the system for leakage before resuming unmanned operation.
During an unmanned period on a UMS vessel the “low water level” alarm for the jacket cooling water system expansion tank activates. What action would you take as duty engineer?
Answer the alarm then block the alarm and change to manned engine room condition.
Answer the alarm then block the alarm function for later action and resume unmanned operation.
Answer the alarm and adjust the alarm set point for the water level in the expansion tank before resuming unmanned operation.
Answer the alarm, top up the tank and check the system for leakage before resuming unmanned operation.
Where would you find out which fire sections are enclosed by “A” or “B” class divisions on a ship?
All the mentioned alternatives.
On the general arrangement plan.
On the capacity plan.
On the Ship’s fire control plans.
What is the objective of the merchant navy?
To earn money for the shipowner.
To transport and deliver goods as quickly as possible.
To provide employment for persons who wish to become seafarers.
To safely transport goods by sea.
During maintenance work on a main diesel engine the fuel injection valve is found to be jammed in the pocket in the cylinder cover. Which of the procedures given in the options should be followed in order to complete the work?
Wedge a bar between the piston top and the bottom of the injector and use the turning gear to force the injection valve out.
Replace the complete cylinder cover with a spare unit and land the cover with the jammed valve ashore for repair in a specialist workshop.
Remove the cylinder cover and try and drive the injection valve out of the pocket from the underside with a hammer and punch.
With the fuel injection valve retaining nuts removed admit compressed air into the engine cylinder to try and blow the injection valve out of the pocket.
Is it necessary to cool the samples taken from a diesel engine cooling water system before carrying out tests to determine the concentration of treatment chemicals?
No, the test should be carried out at system temperature.
Yes, the samples should be cooled to approximately 25 °C.
Yes, the samples should be cooled to approximately 50 °C.
No, the samples should be heated to approximately 95 °C.
An earth fault exists on the blue line of a 100 A bilge pump circuit. A second earth fault occurs on the yellow line of a 10 A ventilation fan circuit. Both systems are supplied from the ship’s 440 V supply. The likely outcome is that:
A short circuit occurs between earth faults and the ventilation fan fuse blows.
An open circuit occurs between earth fault and both motors trip out.
A short circuit occurs between earth fault and the bilge pump fuse blows.
Both motors trip out on overload.
What is the correct name of the tool shown in the illustration?
Flat file.
Chisel.
Pliers.
Grinding machine.
PT-100 sensors are some times used with 3 or 4 wires. What is the reason for this?
Higher mechanical strength of the cable.
For fault indication.
Because of power-consumption.
Higher measuring accuracy.
You are starting to get low on water in the lifeboat. What should you do?
Use sea water.
Collect rain water.
Drink urine.
Mix sea water with 50 % fresh water.
What is the period of validity of the Safety Management Certificate?
1 year.
5 years.
6 months.
2 years.
A flame detector is activated by:
Smoke, gas, sparks and high temperature.
The radiation of heat given off by flames.
The rise of the environment temperature.
The infrared radiation and ultraviolet radiation given off by flames.
When referring to onboard oil treatments using a centrifuge, what is meant by the term purification?
Separation of solid contaminants from a liquid during the process.
Separation of two insoluble liquids with different densities, and the removal of solids in the same process.
It is a general term applied to a process for cleaning oil using a centrifuge.
Separation of one insoluble liquid from another.
An air compressor is being refitted in the engine room. The compressor and motor are coupled using a flexible coupling and are mounted on a common “skid” which fixed to the deck with resilient mountings. Which of the statements, from the options given, relating to the alignment of the motor and compressor is true?
Shims should be fitted between the motor and compressor feet and the skid to ensure correct vertical, horizontal and parallel alignment of the coupling halves before it is bolted up.
As long as the two coupling halves are at the same height the flexible coupling will accommodate any horizontal misalingment of difference in the gap between the coupling faces.
The compressor and motor can just be placed directly on the common skid as they will probably be closely aligned anyway.
Machines using flexible couplings and resilient mountings do not need to be aligned. That is why they have flexible and resilient elements fitted.
The packed gland on a centrifugal pump is leaking even though the gland has been “nipped up”. What is the correct action to take to stop the leakage?
Tighten up the gland as much as possible until the leakage stops.
Ensure the bilge well to which the leakage is draining is regularly pumped out.
Re-pack the stuffing box loosely with the correct size packing at the earliest opportunity.
Fit an extra ring of oversize packing to the stuffing box at the earliest opportunity.
Which ships does the ISM code apply to?
Only passenger vessels.
All passenger ships, all cargo ships of 500 GRT or above.
Only tankers and Ro-ros.
All craft above 300 GRT.
In a low pressure auxiliary boiler, what would be considered to be the maximum allowable chloride level of the boiler water?
600 PPM.
1 000 PPM.
300 PPM.
50 PPM.
Which diagram is the symbol for a THYRISTOR?
Figure 3.
Figure 4.
Figure 2.
Figure 1.
During maintenance of a piston rod stuffing box on a large, slow speed diesel engine it is usual to measure the butt gaps between the sealing ring and scrapper ring segments. What would be the effect of these gaps being too small?
If the gaps are too small the rings could scope the piston rod.
If the gaps are too small they could close due to the radial wear of the rings before the next scheduled overhaul preventing the rings from contacting the piston rod and sealing it.
If the gaps are too small then the flow of scavenge air through the gland would be reduced and the gland would overheat.
If the gaps were too small then no oil could pass up the piston rod to lubricate the sealing rings.
Why is it important to check the timing of diesel engine cylinder oil lubricators?
To ensure the piston is not covering the lubrication points and blocking the flow of cylinder lubricating oil into the cylinder.
To ensure cylinder lubricating oil enters the cylinders when the piston is in the required position.
To ensure the correct amount of cylinder lubricating oil is fed into the cylinders.
To avoid excess pressure in the cylinder lubrication system.
A vapour compression refrigiration system is usually fitted with a number of devices to give protection and control of the system. Which of the methods given in the options should be used to test the high pressure cut out during routine maintenance and checking of the system?
Manually close each of the evaporator coils by switching off the electrical supply to the liquid line solenoid shut off valves and monitor the condenser pressure.
Close the condenser outlet valve and closely monitor the condenser pressure.
Gradually shut in the condenser cooling water valve or the condenser refrigerant inlet valve while closely monitoring the compressor discharge pressure.
Charge the system with refrigerant until the high pressure cut out operates.
What function is this operational amplifier circuit performing?
Integrator.
Differentiator.
Non-inverting amplifier.
Inverting amplifier.
During maintenance of a pneumatically operated, diaphragm actuated control valve the diaphragm is found to be split. Select, from the options given, a suitable material to use to make a temporary replacement if there is no spare diaphragm available.
Natural rubber sheet of approximately the same thickness and elasticity as the original diaphragm material.
Cotton reinforced rubber insertion sheet of smaller thickness but similar strength as the original diaphragm material.
Natural rubber sheet of greater thickness and lower elasticity as the original diaphragm material.
Cotton reinforced rubber insertion sheet of approximately the same thickness but less elasticity than the original diaphragm material.
With two alternators running in parallel, and one is to be disconnected. The first step is to:
Remove the load from the alternator to be stopped.
Increase the frequency on the switchboard.
Trip the main circuit breaker.
Make sure the load is evenly shared.
What is the best method to use to remove heavy scale and fouling from the plates of a heat exchanger?
Use high-pressure cleaner with abrasive additives.
Soak the plates in recommended cleaning solution and then use a soft brush or pressure cleaner.
Use wire-brush metal scrapers and chipping guns.
Renew the plates.
Which of the following instruments is normally part of a control-loop?
Transducer.
Plotter.
Gauge.
Indicator.
What is generally considered as the minimum safe time period before opening a crankcase door after the oil mist detector alarm has activated and the engine has been stopped?
After at least 20 minutes.
After at least 5 minutes.
After at least 1 hour.
After at least 10 minutes.
A seawater pump requires overhaul but there are no spare wear rings for the casing and impeller. It is decided that new wear rings will be fabricated onboard using the ship’s lathe. What would be the most suitable material to use to fabricate the rings onboard?
Mild steel.
Aluminium brass.
Aluminium.
Zinc.
The subject “Engine, Operational, Slow Speed” covers both theoretical and practical aspects of safely working with electrical equipment. Mastery of this material is a direct indicator of an employee’s competence in holding a relevant position aboard a vessel. A sailor in the engine department is responsible for maintaining and adjusting engine components, cooling systems, fuel delivery systems, and other related equipment. They are also tasked with monitoring the operation of all machinery, carrying out regular technical inspections, and performing necessary repairs. When handling a low-speed control system (SU), the sailor ensures precise and safe navigation of the vessel, following the captain’s instructions and navigational charts.
- Test type: STCW.
- Version: 6.0.0, 6.0.13.
- Department: Engine.
- Level: Operational.
- Engine: Slow speed.
Nur Segler können Bewertungen hinterlassen. Um eine Bewertung abzugeben, melden Sie sich mit Ihrem Sailor-Konto auf der Website an.
Seien Sie der Erste, der diesen Online-Test bewertet!